ezeio2:driverdetail [ezeio documentation]

Manufacturer: Generac
Product: PowerZone PRO
Model: PowerZone PRO
Class: MODBUS
Updated: 2024-07-02

Registers

#	Name	Unit
1	Remote annunciator	.
2	DI Results 106	.
3	DOF Results 112	.
4	113	.
5	114	.
6	GEN VOLTAGE AN Vx10	V
7	GEN VOLTAGE BN Vx10	V
8	GEN VOLTAGE CN Vx10	V
9	GEN VOLTAGE LN AVG Vx10	V
10	GEN VOLTAGE AB Vx10	V
11	GEN VOLTAGE BC Vx10	V
12	GEN VOLTAGE CA Vx10	V
13	GEN VOLTAGE LL AVG Vx10	V
14	GEN CURRENT A Ax10	A
15	GEN CURRENT B Ax10	A
16	GEN CURRENT C Ax10	A
17	GEN CURRENT AVG Ax10	A
18	GEN CURRENT N Ax10	A
19	GEN APPARENT PWR LL TOTAL	kVA
20	GEN REACTIVE PWR LL TOTAL	kVAr
21	GEN PF LL AVG	.
22	AVR FIELD CURRENT/AVR SCR DELAY ANGLE	A
23	AVR EXCITATION VOLTAGE/FREQUENCY	V
24	GEN FREQ LL HZx10	Hz
25	RPM 1	rpm
26	BATT VOLTAGE Vx100	V
27	BATT CHARGER CURRENT 1	A
28	OIL TEMP 1	°F
29	OIL PRESS 1	psi
30	OIL PRESS 2	psi
31	COOLANT TEMP 1	°F
32	COOLANT TEMP 2	°F
33	COOLANT LEVEL ENGINE 1	%
34	GOVERNOR THROTTLE POSITION 1	.
35	AIR FUEL RATIO DUTY CYCLE 1	.
36	PRE CAT O2 SENSOR 1	.
37	INTAKE MANIFOLD AIR TEMP 1	°F
38	ENGINE_PERCENT_LOAD_AT_SPEED	.
39	ENGINE DESIRED SPEED	rpm
40	BOOST_PRESS_POST_TURBO_1	psi
41	ENGINE_FUEL_DELIVERY_PRESSURE	kPa
42	DIESEL_FUEL_TEMP	.
43	DIESEL_FUEL_FLOW_RATE	.
44	DIESEL_FUEL_LEVEL_1	%
45	INTAKE AIR PRESSURE DELTA FILTER 1	.
46	INTAKE AIR PRESSURE	.
47	??? alarm_global_commands	.
48	alarm_globals	.
49	Engine_Hour_Now	h
50	Engine_Status_Word	.
51	Genset_Status_Word	.
52	??? _maint_life_remaining	.
53	Engine_kW_Hours_Now	kWh
54	_o2_sensor	.
55	_gov_position	.
56	alarm_global	.
57	auto_off_manual	Value
58	battery_charger_current	A
59	battery_voltage_vx100	V
60	def_level	%
61	fuel_level	%
62	fuel_pressure	psi
63	gen_frequency	Hz
64	turbo_boost_pressure	psi
65	intake_air_temperature	°F
66	kw_hours	kWh
67	gen_last_kwhr	kWh
68	last_run_hours	h
69	oil_level	%
70	gen_total_kw	kW
71	gen_total_power_factor	.
72	rpm1	rpm
73	engine_hours_now	h
74	system_status	.
75	battery_temperature	.
76	sync_angle	.
77	alarm_log_idx	.
78	event_log_idx	.
79	gen_switch_closed	State
80	_remote_start	Command

Notes

PowerZone PRO engine controller with communications gateway

Defaut address: 1  or  100
Default baud: 9600

RS-485 connection
B (Pin 14) to DO
A (Pin 12) to D1

DISCLAIMER:
This driver has not been fully validated by eze System.

Generac PowerZone PRO

Registers

Notes