Differences

This shows you the differences between two versions of the page.

--- ezeio2:userinterface:configuration:system [2023-01-18 18:55] – [Cellular information] andreh
+++ ezeio2:userinterface:configuration:system [2025-05-07 22:07] (current) – [System log] andreh
@@ Line 70: / Line 70: @@
 **Server & Client ports**
-Default setting is 502 on both server and client. This is the standard port number established by Modbus.org
+Default setting is 502 on both server and client. This is the standard port number established by Modbus.org. To disable the Modbus/TCP server, set the server port to 0 (zero).
 === Ethernet settings ===
 **IP**
+The local IP of this ezeio device. Leave blank to use DHCP automatic assignment.
 **DNS**
+Only significant if the IP is set. This should be the IP address of a valid DNS server.
+This can be left blank if the ezeio should only use the Ethernet port for LAN communication (Modbus/TCP) and not for server communication.
 **Gateway**
+Only significant if the IP is set. This should be the IP address of the local gateway device.
+This can be left blank if the ezeio should only use the Ethernet port for LAN communication (Modbus/TCP) and not for server communication.
 **Network mask**
+Only significant if the IP is set. IPv4 network mask for the local network.
-**Ethernet ping interval**
+For Modbus/TCP, only /24 or smaller networks are supported. The last octet is used in the driver section to address the Modbus/TCP servers.
-=== Delete ezeio ===
+=== Unregister ezeio ===
-The delete ezeio button removes an ezeio from the account it is registered to. It can then be added to another account. Since an ezeio can be moved between groups within an account, by simply dragging and dropping, this feature is only needed when the new location desired is outside of the current account. Deleting the ezeio has no effect on its configuration or services. Links to dashboard Widgets and reports in the group will be broken.
+The Unregister ezeio button removes an ezeio from the account it is registered to. It can then be added to another account. Since an ezeio can be moved between groups within an account, by simply dragging and dropping, this feature is only needed when the new location desired is outside of the current account. Deleting the ezeio has no effect on its configuration or services. Links to dashboard Widgets and reports in the group will be broken.
 Once deleted, you will need the serial number and registration code to add the ezeio to another account. These are located on the left side of the ezeio and also in the Identity section of the System information.
@@ Line 123: / Line 131: @@
 |Link|{{ezeio2:userinterface:configuration:x.png?direct|}}| No connection | Failed to connect to cell tower |
 |Received signal|{{ezeio2:userinterface:configuration:strike.png?direct|}} | No connection| No network found or signal too weak |
-|Received Signal|{{ezeio2:userinterface:configuration:1_bar.png?direct|}}| Weak signal | Connected, but signal strength is marginal |
+|Received signal|{{ezeio2:userinterface:configuration:1_bar.png?direct|}}| Weak signal | Connected, but signal strength is marginal |
-|Received Signal|{{ezeio2:userinterface:configuration:5_bars.png?direct|}} | Strong signal | Connected, excellent signal strength |
+|Received signal|{{ezeio2:userinterface:configuration:5_bars.png?direct|}} | Strong signal | Connected, excellent signal strength |
 |Signal level|{{ezeio2:userinterface:configuration:dbm.png?direct|}} | Strength of received signal | Lower negative number is stronger signal. Range: -100 dBm = 0%,  -30 dBm = 100%  |
@@ Line 166: / Line 174: @@
 ==== System log ====
-The system log tracks changes in connectivity between the ezeio and the eze.io servers. Time stamps are shown in UTC. Below is a list of system log details and their explainations.
+The system log tracks changes in connectivity between the ezeio and the eze.io servers. Time stamps are shown in UTC. Below is a list of system log details and their explanations.
 | **Type** | **Details** | **Explanation** |
-| Connection | CONNECT CELL | Connection established via cellular network |
 | Connection | CONNECT ETH | Connection established via Ethernet |
-| Connection | DISCONNECT CELL [reason] | The cellular connection was terminated. |
+| Connection | CONNECT CELL | Connection established via cellular network |
-| Connection | DISCONNECT ETH [reason] | The Ethernet connection was terminated. |
+| Connection | DISCONNECT ETH | The Ethernet connection was terminated. |
-| Connection | LINK-LOSS [reason] | The communication was lost / timed out |
+| Connection | DISCONNECT CELL ''[reason]'' | The cellular connection was terminated.|
+| | ''TMAIN'' - Modem stopped responding ||
+| | ''TLINK'' - No heartbeat message from servers received in 10 minutes ||
+| | ''TCONN'' - No acknowledgement received from the servers ||
+| | ''ETH'' - The Ethernet connection was activated ||
+| | ''ATT'' - The cell modem was disconnected from the cell network ||
+| | ''SOCK'' - The TCP socket connection was closed from the remote side ||
+| | ''CELLOFF'' - The cell modem was powered off ||
+| Connection | LINK-LOSS ''[reason]'' | The communication was lost / timed out |
+| | ''VERSION'' - The firmware ID is invalid ||
+| | ''SERIAL'' - The serial number is not recognized ||
+| | ''FINGERPRINT'' - The security certificate is invalid ||
+| | ''CLEAN'' - The link changed (Eth->Cell or Cell->Eth) and the old link status was erased ||
+| | ''ERROR'' - Registration could not complete ||
+| | ''BADDATA'' - Received data was corrupted/incomplete ||
+| | ''BADKEY'' - A step was skipped during registration ||
+| | ''MSGLEN'' - Received data had an invalid size ||
+| | ''MONITOR'' - The server could not allocate necessary resources ||
+| | ''TCPEOF'' - More data was expected, but did not arrive ||
+| | ''TIMEOUT'' - No new data received in 10 minutes ||
+| | ''SHUTDOWN'' - The server was shut down/restarted ||
+| | ''USER'' - The user sent a disconnect request ||
 | Boot | POR | Power-on reset |
 | Boot | EXT,POR Down:1m 21s | External loss of power followed by elapse time |
@@ Line 179: / Line 207: @@
 | Boot | SW | Software caused a reset |
 | Boot | SW Down:1s | Rebooted, followed by elapse time |