Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
ezeio2:userinterface:configuration:devices:driverlist:discretein [2022-06-22 00:38] – johpar | ezeio2:userinterface:configuration:devices:driverlist:discretein [2023-10-13 18:03] (current) – [Status & Registers (right panel)] johpar | ||
---|---|---|---|
Line 1: | Line 1: | ||
==== Discrete Input driver ==== | ==== Discrete Input driver ==== | ||
+ | |||
+ | ==== Configuration settings (center panel) ==== | ||
=== Description === | === Description === | ||
Line 31: | Line 33: | ||
**REGISTER 1 & 2 modes** - Each discrete input is duplicated, providing the opportunity apply two modes of initial processing and two methods of scaling. The ezeio controller' | **REGISTER 1 & 2 modes** - Each discrete input is duplicated, providing the opportunity apply two modes of initial processing and two methods of scaling. The ezeio controller' | ||
- | **Register 1 & 2 modes** - Choose one of the setting below for registers 1 & 2. | + | **Register 1 & 2 modes** - These modes control how the analog to digital converter calculates the live values. //Separate settings on the individual " |
| **Mode** | **Description** | **Effect** | | | **Mode** | **Description** | **Effect** | | ||
Line 46: | Line 48: | ||
**SCALING OF REGISTER 1** - Register 1 can be scaled to a unit value such as PSI or LPM with a 2 point linear conversion method. A rough conversion can be obtained by entering corresponding values from a table supplied by the sensor manufacture. For a calibrated conversion, use a trusted gauge or probe to provide readings at two points within the sensors range. Enter the value for one point and use the driver' | **SCALING OF REGISTER 1** - Register 1 can be scaled to a unit value such as PSI or LPM with a 2 point linear conversion method. A rough conversion can be obtained by entering corresponding values from a table supplied by the sensor manufacture. For a calibrated conversion, use a trusted gauge or probe to provide readings at two points within the sensors range. Enter the value for one point and use the driver' | ||
- | {{: | + | {{: |
**Raw value point A & B** - By default, the range shown here is set based on the "Input hardware type" selected, such as 0-10V (0.0 - 10.0) or 0-30mA (4.0 - 20.0). This would correlate to the full scale of a typical sensor. These fields can be changed if required to match the output of your sensor or the scale range you wish to use in the next step. | **Raw value point A & B** - By default, the range shown here is set based on the "Input hardware type" selected, such as 0-10V (0.0 - 10.0) or 0-30mA (4.0 - 20.0). This would correlate to the full scale of a typical sensor. These fields can be changed if required to match the output of your sensor or the scale range you wish to use in the next step. | ||
Line 68: | Line 70: | ||
**Logic** - Set the true (or ON) state to be above or below the threshold value, with a value of 1 or 100. Choosing 100, make it easy to use the value to drive a digital output via " | **Logic** - Set the true (or ON) state to be above or below the threshold value, with a value of 1 or 100. Choosing 100, make it easy to use the value to drive a digital output via " | ||
- | ==== Thermistor options ==== | + | ==== Thermistor options |
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
Line 83: | Line 85: | ||
| TX1001 Pro | ThermoWorks | TX-1001X-OP | | | | TX1001 Pro | ThermoWorks | TX-1001X-OP | | | ||
| ET7273 | | ET7273 | | | | ET7273 | | ET7273 | | | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== Status & Registers (right panel) ==== | ||
+ | |||
+ | ---- | ||
+ | |||
+ | === Device Status === | ||
+ | |||
+ | **Driver info** - Typically this is the name from the program file | ||
+ | |||
+ | **Driver updated/ | ||
+ | |||
+ | **Battery & Signal** - Signal indicates the progress through the script. If driver fails to operate, signal number indicates progress | ||
+ | |||
+ | **Driver status** - Color and text of status bubbles give a quick visual reference of Communication, | ||
+ | |||
+ | **Communication** - Com count indicates number of successful and unsuccessful data packets received | ||
+ | |||
+ | ---- | ||
+ | |||
+ | === Available registers === | ||
+ | |||
+ | | 1 | Raw electrical value | Unit type is set by "Input hardware type", V, mA, Ohm | | ||
+ | | 2 | Raw electrical value | Unit type is set by "Input hardware type", V, mA, Ohm | | ||
+ | | 3 | Scaled value, Register 1 | Scaled by 2 point calibration | | ||
+ | | 4 | Scaled value, Register 2 | Scaled by offset and factor | | ||
+ | | 5 | Logical state | Analog value converted to digital (on/off) based on threshold setting | | ||
+ | | 6 | Logical cycles | Number of times " | ||
+ | | 7 | Logical active time | Number of seconds logical state is " | ||
+ |